|
PE3C6202-50CM
D#: PE3C6202-50CM
|
Pasternack Enterprises
|
Key Specifications, Connector Series 1: N, Connector Gender 1: Male, Connector Polarity 1: Standard, Connector Angle 1: Straight, Connector Mount Method 1: None, Connector Impedance 1: 50 Ohm, Connector Series 2: N, Connector Gender 2: Male, Connector Polarity 2: Standard, Connector Angle 2: Straight, Connector Mount Method 2: None, Connector Impedance 2: 50 Ohm, RF Cable Part Number: SPP-250-LLPL, RF Cable Type: SPP-250-LLPL, RF Cable Impedance: 50 Ohm, Length: 19.685 inches. Plenum N Male to N Male Low PIM Cable 50 cm Length Using SPP-250-LLPL Coax Using Times Microwave Parts., Radio frequency assembly plenum N male to N male low PIM cable 50 cm length using SPP-250-LLPL coax using Times Microwave parts from Pasternack is part of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack low PIM (Passive Intermodulation, also called Intermod for short) coaxial cable assembly products are used in applications requiring high quality such as laboratory RF test and measurement, rugged and designed for defense / military, telecom antenna tower component jumper connection, production environments, general use, etc. Plenum N male to N male low PIM cable 50 cm length using SPP-250-LLPL coax using Times Microwave parts, like our other Pasternack coaxial cable assemblies, will ship the same day and any custom TC-250-NM-LP type N to TC-250-NM-LP N type cable assembly orders will ship same day as well. Pasternack RF coax low PIM cable assembly is built with TC-250-NM-LP type N cable connection on one end and TC-250-NM-LP N type cable connection on the other. Our low PIM TC-250-NM-LP type N to TC-250-NM-LP type N cable assemblies have a male gender on end 1 and male on end 2. This TC-250-NM-LP type N to TC-250-NM-LP type N cable is a male to male coax assembly, PE3C6202-50CM, can also be known as a low PIM TC-250-NM-LP N type plug to TC-250-NM-LP type N plug cable assembly and will be shipped same-day as it is purchased. TC-250-NM-LP N type plug to TC-250-NM-LP type N plug cable assembly PE3C6202-50CM is built with SPP-250-LLPL which is a corrugated coax type. The Pasternack low passive intermodulation corrugated TC-250-NM-LP N cable assembly is manufactured with TC-250-NM-LP type N to TC-250-NM-LP type N cable connectors, has a 50 Ohm impedance and is single shielded. RF specs on this 5.8 GHz maximum frequency low PIM TC-250-NM-LP N type male to TC-250-NM-LP type N male cable are located on the specifications PDF datasheet on this page along with CAD drawing and dimensions. Low PIM TC-250-NM-LP N type plug to TC-250-NM-LP type N plug cable assembly is just one of more than 45,000 in-stock RF products available. Pasternack is where to buy a high quality TC-250-NM-LP type N to TC-250-NM-LP N type cable assembly for quick shipment worldwide. Variations of TC-250-NM-LP type N cable assemblies can also be built and will ship same-day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component inter-connection and more for RF test & measurement labs, rugged and MIL-STD designed military / defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For all these reasons and more, Pasternack is one of the best websites where to find and buy quality RF cable assemblies like this plenum N male to N male low PIM cable 50 cm length using SPP-250-LLPL coax using Times Microwave parts.
Min Qty:
1
Package Multiple:
1
|
798
|
- 1 $103.9900
- 25 $98.7900
- 50 $93.5900
- 100 $89.4300
- Show All
|
Buy Now
|
|
PE3FCA202-5M
D#: PE3FCA202-5M
|
Pasternack Enterprises
|
Key Specifications, Mode: Multimode, Multimode Class: OM4, Fiber Diameter: 50/125, Cable Assembly Color: Aqua Blue, Return Loss Min: 30 dB, Insertion Loss Max: 0.3 dB, Connector 1 Series: LC, Connector 1 Polish Type: UPC, Connector 2 Series: SC, Connector 2 Polish Type: UPC, Jacket Burn Rating: OFNP, Cable Diameter: 4.5 mm, Max Crush Resistance, Short Term (N/100mm): 1,000, Max Crush Resistance, Long Term (N/100mm): 300, Max Operating Temperature: 60 deg C, Min Operating Temperature: 0 deg C, Ingress Protection (IP) Rating: Non-Rated. 4-Fiber LC UPC to SC UPC, OM4 Multimode Distribution Cable, 4.5mm Plenum, 2.0mm breakout, Aqua-5M. Pasternack’s PE3FCA202-5M fiber optic breakout cord is a robust and versatile fiber optic cable assembly designed for high-performance data transmission in various environments. This 5-meter long 4-fiber cable assembly is equipped with LC/UPC to SC/UPC connectors. Our aqua blue fiber optic cable has a plenum (OFNP) rated PVC jacket that ensures compliance with fire and safety standards. With an operating temperature range of 0 to 60 degrees C and a storage temperature range of -20 to 60 degrees C, this cable provides reliable performance across diverse conditions. This distribution cable assembly comes with a multimode OM4 fiber that supports 10Gb Ethernet up to 550 meters and 40G/100G Ethernet up to 150 meters and a bandwidth of 4700 MHz.km that delivers low attenuation and high-speed performance for mission-critical applications. The fiber optic jumper from Pasternack is suitable for applications such as data centers, passive optical networks (PON), local area networks (LAN), enterprise networking, storage and cloud based services, AI data storage and communications, headend termination to a fiber backbone and terminations of data center fiber rack system. Additional dimensions, specifications, and CAD drawings for this 4-strand fiber optic breakout cord component can be found on its downloadable PDF datasheet. This PE3FCA202-5M fiber optic cable with a 4.5 mm cable diameter and 34 mm bend radius offers flexible installation options. Pasternack has one of the largest in-stock selections of LC/UPC to SC/UPC fiber optic breakout cords for international and domestic orders. Make your online purchase right now to take advantage of our same-business-day shipping. Our fiber optic breakout assembly is designed for hyperscale data centers and telecom backbones and ensures seamless network connectivity with minimal signal loss. For further information on similar products, our expert technical support and knowledgeable sales team can help you get the ideal OM4 multimode fiber optic cable that meets your requirements.
Min Qty:
1
Package Multiple:
1
|
46
|
- 1 $141.9900
- 5 $136.3100
- 10 $130.6300
- 25 $124.9500
- Show All
|
Buy Now
|
|
PE3FCA420-25M
D#: PE3FCA420-25M
|
Pasternack Enterprises
|
Key Specifications, Mode: Multimode, Multimode Class: OM4, Fiber Diameter: 50/125, Cable Assembly Color: Aqua Blue, Return Loss Min: 30 dB, Insertion Loss Max: 0.3 dB, Connector 1 Series: LC, Connector 1 Polish Type: UPC, Connector 2 Series: SC, Connector 2 Polish Type: UPC, Jacket Burn Rating: LSZH, Cable Diameter: 6.2 mm, Max Crush Resistance, Short Term (N/100mm): 1,000, Max Crush Resistance, Long Term (N/100mm): 300, Max Operating Temperature: 70 deg C, Min Operating Temperature: -20 deg C, Ingress Protection (IP) Rating: Non-Rated. 12-Fiber LC UPC to SC UPC, OM4 Multimode Distribution Cable, 6.2mm LSZH, 2.0mm breakout, Aqua-25M. Pasternack’s PE3FCA420-25M fiber optic breakout cord is a robust and versatile fiber optic cable assembly designed for high-performance data transmission in various environments. This 25-meter long 12-fiber cable assembly is equipped with LC/UPC to SC/UPC connectors. Our aqua blue fiber optic cable has an LSZH (low smoke zero halogen) rated PE jacket that ensures compliance with fire and safety standards. With an operating temperature range of -20 to 70 degrees C and a storage temperature range of -40 to 70 degrees C, this cable provides reliable performance across diverse conditions. This distribution cable assembly comes with a multimode OM4 fiber that supports 10Gb Ethernet up to 550 meters and 40G/100G Ethernet up to 150 meters and a bandwidth of 4700 MHz.km that delivers low attenuation and high-speed performance for mission-critical applications. The fiber optic jumper from Pasternack is suitable for applications such as data centers, passive optical networks (PON), local area networks (LAN), enterprise networking, storage and cloud based services, AI data storage and communications, headend termination to a fiber backbone and terminations of data center fiber rack system. Additional dimensions, specifications, and CAD drawings for this 12-strand fiber optic breakout cord component can be found on its downloadable PDF datasheet. This PE3FCA420-25M fiber optic cable with a 6.2 mm cable diameter and 47 mm bend radius offers flexible installation options. Pasternack has one of the largest in-stock selections of LC/UPC to SC/UPC fiber optic breakout cords for international and domestic orders. Make your online purchase right now to take advantage of our same-business-day shipping. Our fiber optic breakout assembly is designed for hyperscale data centers and telecom backbones and ensures seamless network connectivity with minimal signal loss. For further information on similar products, our expert technical support and knowledgeable sales team can help you get the ideal OM4 multimode fiber optic cable that meets your requirements.
Min Qty:
1
Package Multiple:
1
|
15
|
- 1 $405.9900
- 5 $389.7500
- 10 $373.5100
- 25 $357.2700
- Show All
|
Buy Now
|
|
PE88X2025
D#: PE88X2025
|
Pasternack Enterprises
|
Key Specifications, Output Connector: WR-12 Waveguide with UG-387/U Flange, Connector Input: SMA Female, Minimum Output Frequency: 60 GHz, Maximum Output Frequency: 90 GHz, Output Frequency Band: E band, Multiplication Factor: 6 X, Multiplier Type: Active, Typical Output Power: 20 dB, Typical Input Power: 3 dB. WR-12 Waveguide with UG-387/U Flanged 6x Active Frequency Multiplier, E band, 60 GHz to 90 GHz Frequency and +20 dBm Power Outputs. All WR-12 waveguide with UG-387/U flanges active 6X multipliers, (aka doublers) from Pasternack's exclusive waveguide frequency connector series, have same-day shipping internationally for all online or phone-in purchases. We supply over 100,000 microwave, RF, and millimeter-wave components including these frequency 6X waveguide doublers (or multipliers) PE88X2025 that can multiply an input power ranging as low as 1 dBm to 3 dBm into as much as 20 dBm. Our active frequency 6X multiplier is manufactured to handle a E band frequency input range of 10 GHz to 15 GHz and E band 60 GHz to 90 GHz output. Call or go online to get PE88X2025 active 1 dBm to 3 dBm waveguide doublers with that are kept in our facility certified to ISO 9001:2015, stocked for same-day, worldwide trade. These microwave doublers with UG-387/U can multiply a 10 GHz to 15 GHz input signal into a larger harmonic output of E band 60 GHz to 90 GHz. Pasternack is the optimal place to buy rugged aluminum waveguide radio frequency doublers because unlike our competitors, we keep active multipliers model PE88X2025 with feed-thru-pin SMA female flanges constantly in stock. Expert technical support and 60 GHz to 90 GHz industry-leading output frequency are just two things that are always available with our top-tier female SMA 6X multipliers with -15 dBc harmonic suppression and UG-387/U pin connectors. Pasternack offers a deep and broad selection of over 100,000 RF microwave components like this frequency multiplier with 231 mA of DC current and SMA female to WR-12 waveguide with UG-387/U flanges and feed-thru-pin connectors. 6X multipliers with -15 dBc harmonic suppression send 60 GHz input signals through bandpass filters to select the desired harmonics multiplied to 90 GHz output. These WR-12 waveguide with UG-387/U flanges feed-thru-pin waveguides with aluminum UG-387/U flanged connectors have a typical input VSWR (voltage standing wave ratio) of 2.5:1 and a DC current bias of 231 mA. E band waveguide 3 dBm to 20 dBm doublers operate at -15 dBc harmonic suppression in the E band 60 GHz to 90 GHz range of frequencies. Throughout the whole process of E band signal and power amplification this 60 GHz to 90 GHz frequency multiplier with waveguide connection typically has an input drive level between 1 - 10 dBm and a maximum loss of only -15 dB. The waveguide SMA female series UG-387/U flanges connection can withstand input frequencies of 10 GHz - 15 GHz multiplied to 90 GHz - 60 GHz, are globally available for shipping ISO 9001:2015 certified, with CAD drawings for each WR-12 waveguide with UG-387/U flanges aluminum feed-thru-pin frequency doubler purchased. Pasternack well-made doubler E band WR-12 waveguide with UG-387/U flanges frequency active multipliers are regularly used for communication test equipment and applications of RADAR/satellite/wireless, across the E band 60 GHz-90 GHz frequencies. Downloadable dimensions and specifications in our PDF datasheets avaiable: height of 1.704 in., width of 1.673 in., length of 1.673 in., are REACH compliant operating in the temperature range of -40°C - 80°C and ship fast the same day you ordered. For questions or aid in ordering WR-12 waveguide with UG-387/U flanges active no limit multiplier modules just trust in the Pasternack.com specialized customer service sales team and check-out our hassle-free online interface here for 10 dBm 6X multipliers.
Min Qty:
1
Package Multiple:
1
|
1
|
- 1 $12,150.0000
- 25 $11,542.5000
- 50 $10,935.0000
- 100 $10,449.0000
- Show All
|
Buy Now
|
|
PE7202-50
D#: PE7202-50
|
Pasternack Enterprises
|
Key Specifications, Design: Fixed, Maximum Frequency: 6 GHz, Impedance: 50 Ohm, Power Maximum: 100 Watt, VSWR Maximum: 1.45:1, Attenuation: 50 dB, Connector Series 1: N, Connector Gender 1: Female, Connector Series 2: 7/16 DIN, Connector Gender 2: Male, Body Material: Black Anodized Aluminum Heatsink. 50 dB Fixed Attenuator, N Female To 7/16 DIN Male Directional Black Anodized Aluminum Heatsink Body Rated To 100 Watts Up To 6 GHz. PE7202-50 is a fixed 50 dB attenuator from Pasternack. This 50dB attenuator is an in-line, resistive PI attenuator pad design. Our coaxial 50 Ohm attenuator is manufactured to precise RF / microwave industry specifications. This type N attenuator has a female gender on side 1 and a 7/16 DIN male connector on side 2. The Pasternack PE7202-50 50 dB attenuator is rated for up to 6 GHz. Our microwave attenuator is rated to 100 Watts at the stated attenuation value. Our fixed RF attenuator PE7202-50 is shipped same-day as purchased from Pasternack's production facility certified to ISO 9001:2015. This 50dB attenuator is part of over 40,000 RF, microwave and millimeter wave products that ship the same day worldwide, including custom cable assemblies.
Min Qty:
1
Package Multiple:
1
|
1
|
- 1 $1,100.0000
- 5 $1,056.0000
- 10 $1,012.0000
|
Buy Now
|
|
PE3W20257/HS
D#: PE3W20257/HS
|
Pasternack Enterprises
|
Key Specifications, Connector Series 1: TNC, Connector Gender 1: Male, Connector Polarity 1: Standard, Connector Angle 1: Straight, Connector Mount Method 1: None, Connector Impedance 1: 50 Ohm, Connector Series 2: TNC, Connector Gender 2: Male, Connector Polarity 2: Standard, Connector Angle 2: Straight, Connector Mount Method 2: None, Connector Impedance 2: 50 Ohm, RF Cable Part Number: LMR-195-FR, RF Cable Type: LMR-195-FR, RF Cable Impedance: 50 Ohm. TNC Male to TNC Male Cable Using LMR-195-FR Coax with HeatShrink. PE3W20257/HS is a TNC male to TNC male cable using LMR-195-FR coax. This Pasternack TNC male to TNC male cable assembly uses a 50 Ohm TNC for connector 1 and a 50 Ohm TNC for connector 2. Our male TNC to male TNC cable assembly uses a flexible cable type that is 50 Ohm. Pasternack PE3W20257/HS TNC male to TNC male cable assembly is constructed with LMR-195-FR coax, * LMR™ is a trademark of Times Microwave Systems.
Min Qty:
1
Package Multiple:
1
|
0
|
|
Buy Now
|
|
PE3W20254
D#: PE3W20254
|
Pasternack Enterprises
|
Key Specifications, Connector Series 1: BNC, Connector Gender 1: Male, Connector Polarity 1: Standard, Connector Angle 1: Straight, Connector Mount Method 1: None, Connector Impedance 1: 50 Ohm, Connector Series 2: BNC, Connector Gender 2: Male, Connector Polarity 2: Standard, Connector Angle 2: Right Angle, Connector Mount Method 2: None, Connector Impedance 2: 50 Ohm, RF Cable Part Number: RG303/U, RF Cable Type: RG303, RF Cable Impedance: 50 Ohm. BNC Male to BNC Male Right Angle Cable Using RG303 Coax. PE3W20254 is a BNC male to BNC male right angle cable using RG303 coax. This Pasternack BNC male to BNC male right angle cable assembly uses a 50 Ohm BNC for connector 1 and a 50 Ohm BNC for connector 2. BNC to BNC right angle coaxial cable assembly uses 90 degree right angle coax cable connector. Our male BNC to male BNC right angle cable assembly uses a flexible cable type that is 50 Ohm. Pasternack PE3W20254 BNC male to BNC male right angle cable assembly is constructed with RG303 coax.
Min Qty:
1
Package Multiple:
1
|
0
|
|
Buy Now
|
|
PE3W12025LF
D#: PE3W12025LF
|
Pasternack Enterprises
|
Key Specifications, Connector Series 1: QMA, Connector Gender 1: Female, Connector Polarity 1: Standard, Connector Angle 1: Straight, Connector Mount Method 1: None, Connector Impedance 1: 50 Ohm, Connector Series 2: 4.3-10, Connector Gender 2: Male, Connector Polarity 2: Standard, Connector Angle 2: Right Angle, Connector Mount Method 2: None, Connector Impedance 2: 50 Ohm, RF Cable Part Number: SPF-250, RF Cable Type: SPF-250, RF Cable Impedance: 50 Ohm. QMA Female to 4.3-10 Male Right Angle Cable Using SPF-250 Coax, LF Solder. PE3W12025LF is a QMA female to 4.3-10 male right angle cable using SPF-250 coax. This Pasternack QMA female to 4.3-10 male right angle cable assembly uses a 50 Ohm QMA for connector 1 and a 50 Ohm 4.3-10 for connector 2. QMA to 4.3-10 right angle coaxial cable assembly uses 90 degree right angle coax cable connector. Our female QMA to male 4.3-10 right angle cable assembly uses a corrugated cable type that is 50 Ohm. Pasternack PE3W12025LF QMA female to 4.3-10 male right angle cable assembly is constructed with SPF-250 coax.
Min Qty:
1
Package Multiple:
1
|
0
|
|
Buy Now
|
|
PE3W20255
D#: PE3W20255
|
Pasternack Enterprises
|
Key Specifications, Connector Series 1: F, Connector Gender 1: Male, Connector Polarity 1: Standard, Connector Angle 1: Straight, Connector Mount Method 1: None, Connector Impedance 1: 75 Ohm, Connector Series 2: F, Connector Gender 2: Male, Connector Polarity 2: Standard, Connector Angle 2: Straight, Connector Mount Method 2: None, Connector Impedance 2: 75 Ohm, RF Cable Part Number: LMR-240-75-DB, RF Cable Type: LMR-240-75-DB, RF Cable Impedance: 75 Ohm. 75 Ohm F Male to 75 Ohm F Male Cable Using 75 Ohm LMR-240-75-DB. PE3W20255 is a F male to F male cable using LMR-240-75-DB coax. This Pasternack F male to F male cable assembly uses a 75 Ohm F for connector 1 and a 75 Ohm F for connector 2. Our male F to male F cable assembly uses a flexible cable type that is 75 Ohm. Pasternack PE3W20255 F male to F male cable assembly is constructed with LMR-240-75-DB coax, * LMR™ is a trademark of Times Microwave Systems.
Min Qty:
1
Package Multiple:
1
|
0
|
|
Buy Now
|
|
PE3W20255LF/HS
D#: PE3W20255LF/HS
|
Pasternack Enterprises
|
Key Specifications, Connector Series 1: F, Connector Gender 1: Male, Connector Polarity 1: Standard, Connector Angle 1: Straight, Connector Mount Method 1: None, Connector Impedance 1: 75 Ohm, Connector Series 2: F, Connector Gender 2: Male, Connector Polarity 2: Standard, Connector Angle 2: Straight, Connector Mount Method 2: None, Connector Impedance 2: 75 Ohm, RF Cable Part Number: LMR-240-75-DB, RF Cable Type: LMR-240-75-DB, RF Cable Impedance: 75 Ohm. 75 Ohm F Male to 75 Ohm F Male Cable Using 75 Ohm LMR-240-75-DB with HeatShrink, LF Solder. PE3W20255LF/HS is a F male to F male cable using LMR-240-75-DB coax. This Pasternack F male to F male cable assembly uses a 75 Ohm F for connector 1 and a 75 Ohm F for connector 2. Our male F to male F cable assembly uses a flexible cable type that is 75 Ohm. Pasternack PE3W20255LF/HS F male to F male cable assembly is constructed with LMR-240-75-DB coax, * LMR™ is a trademark of Times Microwave Systems.
Min Qty:
1
Package Multiple:
1
|
0
|
|
Buy Now
|
Microchip Technology Inc 
TE Connectivity 
Rochester Electronics 
SiTime Corporation 
Master Electronics 
Coilcraft Direct 
Flip Electronics 
Dynamic Solutions GmbH 
Powell Electronics 
Unikey Electronic Pte Ltd 
PUI 
Time Way Electronics Limited 
Bristol Electronics 
Ameya Holding Limited 
Hermes Engineering 
Sensible Micro Corporation 
Richardson RFPD 
ICMILES Electronics Ltd 
ICHOME Technology 
ComSIT USA 
Kepictronics Inc. 
North Star Micro Electronics 
Kurrent Technology 
Sager 
DB Roberts 
Chip-Germany GmbH 
Component Stockers 
Interstate Connecting Components 
PEI Genesis 
Microchip USA 
NAC 
Quest Components 
Tencell 
Unicom Electronics 
New Advantage Corporation
Silitech Components Inc. 
Chip Stock 
Shengyu Electronics Technology Limited 
Avnet Abacus 
YIC International Co., Limited 
ICHOT TECHNOLOGY LIMITED 
Avnet Silica 
Sierra IC 
Unibetter Technology Co., Ltd 
R&J Components 
ACDS 
Venkel Ltd. 
Win Source Electronics 
Vyrian 
Futuretech Components Ltd 
Sense Electronic Company Limited 
Cytech Systems Limited 
LIBRA Elektronik GmbH 
Greenchips 
Neutron USA 
IC Components Limited 
Perfect Parts Corporation 
MountainView Components Inc. 
EBV Elektronik 
GlobalTek Components 
Tedss 
NexGen Digital
Pasternack Enterprises US